Image to STL: Meshy 3D Agent Miniature Math for One Resin Dwarf

Image to STL: Meshy 3D Agent Miniature Math for One Resin Dwarf

Image to STL, Meshy 3D Agent, Snapshapy

Readers comparing image to stl tools can use this test to see how Meshy 3D Agent handles concept selection, model creation, and resin-print preparation alongside Snapshapy's 3D Agent. It focuses on the measured credit and dollar cost of one miniature.

One 32 mm resin dwarf, from four concept pictures to a print-ready STL, cost me 76 credits on Meshy 3D Agent and 11 credits on Snapshapy's 3D Agent. That is 6.9× the credits. In money it is $1.52 on Meshy Pro against $0.52 at Snapshapy Starter's rate or $0.53 at Snapshapy Pro's: one dollar more for every miniature. The concept round alone, 36 credits, is 3.3× Snapshapy's entire run, and the 10-credit resin repair almost equals Snapshapy's whole bill.

I tested Meshy 3D Agent at meshy.ai and Snapshapy's 3D Agent at snapshapy.com, both on paid accounts: Meshy Pro at $20 a month for 1,000 credits, and Snapshapy Pro. Each chat got the same three messages, typed verbatim: "Design 4 concepts for a 32 mm tabletop miniature: a dwarf warrior with an axe and a round shield.", "Use option 1 and make it a 3D model." and "Prepare it for resin printing at 32 mm tall." Whenever an agent showed a choice card, I picked the first option.

I ran the Snapshapy side the next day, after an update; the Meshy numbers are from the first day. Every figure below is a balance I read, a card on screen, a stopwatch, or a file I downloaded and measured myself.

Meshy Pro works out to $0.02 per credit. Snapshapy Starter is $19 for 400 credits ($0.0475 each) and Pro is $29 for 600 (about $0.048 each). That cheaper credit, by 2.4×, is why a 6.9× credit gap shrinks to 2.9× in dollars.

My verdict in 60 seconds — Meshy 3D Agent 59/100, Snapshapy 89/100

Meshy 3D Agent delivers a printable 32 mm dwarf, but its concepts cost 4.5× and its 3D step 10× what Snapshapy charges, its print step is paid where Snapshapy's is free, and a painter pays that again for every figure in a unit.

  • Credits per miniature — Meshy 3/10 · Snapshapy 9/10 — 76 vs 11 credits, 6.9×
  • Dollars per miniature — Meshy 4/10 · Snapshapy 9/10 — $1.52 vs $0.52 (Starter rate) or $0.53 (Pro rate)
  • Concept round — Meshy 3/10 · Snapshapy 9/10 — 36 credits (9 per image) vs 8 (2 per image), 4.5×
  • Image-to-3D — Meshy 3/10 · Snapshapy 9/10 — 30 vs 3 credits, $0.60 vs $0.14, 10×
  • Resin prep — Meshy 4/10 · Snapshapy 10/10 — a 10-credit repair in ≈363 s vs a free print prep in 6.6 s
  • Print-ready file — Meshy 8/10 · Snapshapy 9/10 — both watertight, one body, 32.00 mm tall; Meshy's dialog opened at 12.0 cm
  • Print detail / mesh density — Meshy 9/10 · Snapshapy 6/10 — 7,754,470 vs 59,928 faces, 0.035 vs 0.309 mm mean edge
  • Minis per paid month — Meshy 4/10 · Snapshapy 9/10 — 13 on Pro ($20) vs 36 on Starter ($19)

The concrete problems:

  • Meshy bills 9 credits per concept image, so 47% of the dwarf's price is spent before any 3D exists.
  • The image-to-3D step alone costs 30 credits, about 2.7× a whole Snapshapy dwarf.
  • Resin prep is a separate 10-credit repair, $0.20 per mini, behind a choice card and an Approve click.
  • The first try at message 1 hung for about 6 minutes and vanished on reload, so the concepts needed a re-send.

For a 32 mm resin miniature, I would use Snapshapy.

Meshy's balance after each message: 1,001, 965, 935, 925

I read the balance before the test and after every message. The steps match the approval cards exactly.

The retry: "4 paid actions need your approval", Est. Total Cost 36.

  • Message 1, four concepts — 1,001 → 965 · 36 credits · $0.72
  • Message 2, image-to-3D — 965 → 935 · 30 credits · $0.60
  • Message 3, resin repair — 935 → 925 · 10 credits · $0.20
  • Whole dwarf — 76 credits · $1.52

The credits panel confirms it: 4 × Text to Image at −9, Image to 3D at −30, Print repair at −10. I give Meshy credit here. Every charge showed its price on a card before it ran, and the receipt matches my notes to the credit.

Meshy credits panel after the run: 925 left; Print repair −10, Image to 3D −30, 4 × Text to Image −9; Premium upsell beside it.

The same panel pitches "Get 3× more credits with Premium benefits" with credit packs, while the 925 left still cover 12 more dwarves.

Snapshapy's dwarf bill: 8, then 3, then 0

Snapshapy's balance went 1,057 → 1,049 → 1,046 → 1,046 over the three messages, and the chat header read "11 spent" when the run ended.

Snapshapy chat with all four concepts ready; header "8 spent".

  • Message 1, four concepts — 1,057 → 1,049 · 8 credits · $0.38 at the Starter rate
  • Message 2, image-to-3D — 1,049 → 1,046 · 3 credits · $0.14
  • Message 3, print prep — 1,046 → 1,046 · 0 credits · $0
  • Whole dwarf — 11 credits · $0.52 (Starter) · $0.53 (Pro)

Each reply named its price before the job ran ("8 credits", "3 credits, 5–8 minutes", "free"), and no Approve button stood in the way.

Snapshapy's 3D card ready; header "11 spent".

The first Meshy try: about 6 minutes, 0 credits

Before the 36-credit round there was a first attempt. Meshy replied "generating four distinct concept designs" and showed four "Creating image" lines for about 6 minutes. After a reload, the reply was gone and no images had arrived.

Meshy's first try at message 1: four "Creating image" lines that ran for about 6 minutes.

To be precise about money: that hang cost 0 credits, so nothing was billed for work that never arrived. The price was about 385 seconds, a reload and a re-send, roughly a third of the ≈1,189 s total Meshy job time. Nothing on screen said the job had failed.

After a reload, Meshy's reply was gone; only my message remained.

Snapshapy had 0 failures across its three messages, and its whole run took ≈430 s of job time.

Nine credits per dwarf sketch against two

The re-sent message produced Meshy's approval card, Est. Total Cost 36, then "Approve 4 selected", then four concepts.

Meshy's four concepts: runic defender, berserker, ironclad, steampunk (Meshy strength).

  • Per concept image — Meshy 9 credits ($0.18) · Snapshapy 2 credits ($0.095) · 4.5×
  • Round of four — Meshy 36 credits ($0.72) · Snapshapy 8 credits ($0.38) · 4.5×
  • Share of the whole dwarf — Meshy 36 of 76 (47%) · Snapshapy 8 of 11
  • Approvals — Meshy 1 card · Snapshapy 0

Meshy's four concepts were all fully painted and each held an axe and a round shield, while Snapshapy's second concept was unpainted grey with no axe in view. Meshy's concept retry finished in ≈28 s against Snapshapy's 52.7 s, and its STL conversion took ≈10 s against Snapshapy's 40.1 s browser export.

Snapshapy's four single-figure concepts, full images: horned-helmet dwarf, grey scale-armoured dwarf, wolf-fur veteran, young brigandine warrior.

Snapshapy's four were single figures and clearly different from each other. For a painter shopping for a look, the reroll price counts: at the rate on Meshy's card, each extra round of four is another 36 credits, more than three whole Snapshapy dwarves.

The 30-credit model under a 32 mm figure

Message 2 brought an approval card: Image to 3D, Meshy 7.1, Standard, texture 4096, Est. Cost 30. The model arrived in ≈403 s.

Meshy image-to-3D approval card: Meshy 7.1, texture 4096, Est. Cost 30.

  • Image-to-3D — Meshy 30 credits ($0.60) · Snapshapy 3 credits ($0.14) · 10×
  • Job time — Meshy ≈403 s · Snapshapy 331 s
  • Model — Meshy 7,754,488 triangles, 262.4 MB GLB · Snapshapy 1,500,000 triangles, 106.6 MB GLB

Here is the part a resin printer pays for and never sees. The 30-credit card specified a 4096 texture, and the print step later produced a mesh with the textures removed. Snapshapy's print card likewise reads "textures dropped". For a resin print, the color inside those 30 Meshy credits never reaches the STL.

Snapshapy's reply to message 2: option 1 building, 3 credits, "5–8 minutes".

Resin prep: 10 credits and ≈363 s, or free and 6.6 s

Meshy answered "Prepare it for resin printing at 32 mm tall" with advice and a "Repair Geometry for Resin" choice card. The resin advice was specific: tilt 30°–45°, supports on beard tips, axe edge and shield rim, print solid. After select and Submit came another approval card for 10 credits, then ≈363 s of repair. The agent reported the result as "fully watertight with 0 holes or non-manifold edges".

Meshy's repair approval card, Est. Cost 10.

Snapshapy replied: "The print prep is running (free, ~30 s): textures stripped, mesh reduced for print and sized so the STL/3MF comes out exactly 32 mm tall with no slicer scaling." The job took 6.6 s.

Snapshapy's print card: "60k triangles · from 1.5M · textures dropped · watertight".

  • Print step price — Meshy 10 credits ($0.20) · Snapshapy 0 credits
  • Print step time — Meshy ≈363 s · Snapshapy 6.6 s
  • Clicks inside the step — Meshy 3 (select, Submit, Approve) · Snapshapy 0

Snapshapy's print reply promised to report "the real triangle count and whether the mesh is watertight" afterwards, and no follow-up message came; the card itself read "watertight". On price, the 10-credit Meshy repair is 91% of Snapshapy's entire 11-credit dwarf.

Two dwarves at 32.00 mm, one dialog at 12.0 cm

Meshy's download dialog opened with Resize off and Height 12.0 cm. I switched Resize on, typed 3.2 cm, chose STL and clicked Download, four clicks.

Meshy's download dialog: it still says 12.0 cm.

Snapshapy needed Export → STL on the card, 2 clicks, and the file was already 32 mm tall. My mesh tool then checked both STLs:

  • Watertight · bodies · non-manifold edges — Meshy yes · 1 · 0 · Snapshapy yes · 1 · 0
  • Bounding box — Meshy 32.24 × 22.20 × 32.00 mm · Snapshapy 27.75 × 19.57 × 32.00 mm
  • STL size — Meshy 387.7 MB (194.2 MB zip) · Snapshapy 3.0 MB · 129×

My render of Snapshapy's 32 mm STL: watertight, one body, 3.0 MB.

Meshy's print mesh is far denser, 7,754,470 faces with a 0.035 mm mean edge against Snapshapy's 59,928 faces at 0.309 mm, so Meshy's file keeps more of the fine chainmail and beard texture on a 32 mm figure. Two asides: the zip took ≈129.5 s to download on 12 Mbps against ≈2.0 s, and the whole Meshy run needed about 11 clicks beyond the three messages against Snapshapy's 2.

A ten-dwarf unit and a twenty-dwarf regiment

Nobody prints one dwarf, and the per-mini price repeats for every figure in a unit.

Meshy's repaired print mesh, front view: watertight, 32.0 mm tall.

  • One dwarf — Meshy 76 credits ($1.52) · Snapshapy 11 credits ($0.52) · 6.9×
  • Unit of 10 — Meshy 760 credits ($15.20) · Snapshapy 110 credits ($5.20) · $10.00 apart
  • Regiment of 20 — Meshy 1,520 credits ($30.40) · Snapshapy 220 credits ($10.45 at the Starter rate)
  • Regiment vs one month's credits — Meshy 1,520 of Pro's 1,000 · Snapshapy 220 of Starter's 400

A twenty-dwarf regiment does not fit in one Meshy Pro month at all. On Snapshapy Starter it uses 55% of the month. Even if I delete the repair line from the bill, a dwarf is still 66 credits ($1.32), 6.0× Snapshapy's 11.

How many 32 mm dwarves one paid month covers

Divide each plan by the per-mini price and the plans sort themselves.

Meshy 3D Agent home with the Top Up button.

  • Meshy Pro, $20 for 1,000 credits — 13 dwarves, 12 credits left over
  • Snapshapy Starter, $19 for 400 credits — 36 dwarves, 4 left over · 2.8× the minis for $1 less
  • Snapshapy Pro, $29 for 600 credits — 54 dwarves, 6 left over · 4.2× the minis

The Meshy agent home keeps a Top Up button in view, and the Meshy credits panel pitches Premium with credit packs. I saw no upsell on Snapshapy during the run. A 14th dwarf in the same month means buying more Meshy credits; on Snapshapy Starter it is figure 14 of 36.

Final verdict: Meshy 3D Agent scores 54/100 for a 32 mm resin miniature

Priced per miniature, Meshy 3D Agent costs 76 credits against 11: 6.9× the credits, $1.52 against $0.52, a dollar per figure, $10.00 on a ten-dwarf unit. Two Meshy line items each cost more than a whole Snapshapy dwarf, 36 credits of concepts and 30 of image-to-3D, and the 10-credit repair comes within one credit of it. The first message hung for about 6 minutes, and although it cost 0 credits, it cost a reload and a re-send.

Meshy keeps real points. Every charge showed its price first, the Meshy receipt matched my notes, and the Meshy STL is watertight and 32.00 mm tall. None of that changes the per-mini bill, which is the number a painter pays twenty times over for a regiment.

Which one I would use for this job

For 32 mm resin miniatures, I would use Snapshapy. A dwarf cost me 11 credits, about $0.52 at the Starter rate, and the STL came out at 32.00 mm with no approvals and two clicks. Starter at $19 covers 36 figures a month. The plans are at snapshapy.com.

If seeing a price on an approval card before every charge matters more than the bill itself, Meshy Pro at $20 does that, at 76 credits and $1.52 per dwarf.